1. Introduction
The rapid advancement of the electric vehicle industry has fundamentally transformed the automotive sector, driven by the dual imperatives of fossil fuel conservation and environmental sustainability. As electric vehicles continue to gain market acceptance, dynamic comfort has emerged as a decisive factor influencing consumer purchasing decisions. Unlike conventional internal combustion engine vehicles, electric vehicles employ electric motors as their sole power source, resulting in fundamentally different powertrain architectures and dynamic response characteristics. The powertrain system of an electric vehicle typically integrates the motor with a reduction gearbox, eliminating traditional components such as torque converters and clutches that provide substantial damping in conventional vehicles. This structural simplification, while enhancing energy efficiency, introduces a significant challenge: the inherently rapid torque response of the drive motor, when coupled with the underdamped characteristics of the transmission system, can induce severe torsional vibrations during acceleration. These vibrations propagate through the drivetrain to the vehicle body, manifesting as longitudinal oscillations and shocks that substantially degrade ride comfort.
The evaluation and optimization of dynamic response quality during acceleration phases constitute a critical technical challenge in the development of high-performance electric vehicles. Traditional evaluation frameworks are predominantly based on objective metrics, such as jerk amplitude and acceleration root mean square, which fail to adequately capture the nuanced subjective experiences of drivers and passengers. Conversely, purely subjective evaluation methods, while reflecting genuine human perception, suffer from inherent limitations including high implementation costs, extended evaluation cycles, and inter-rater variability. This research aims to bridge this gap by proposing an integrated subjective-objective evaluation methodology that incorporates electrocardiogram signals to quantify human physiological responses, thereby establishing a more comprehensive and scientifically rigorous assessment framework.


2. Electromechanical Coupling Modeling and Simulation
2.1 Motor and Vector Control Model
The dynamic behavior of an electric vehicle during acceleration is fundamentally governed by the interaction between the motor’s electromagnetic torque generation and the mechanical response of the drivetrain. For the permanent magnet synchronous motor employed in this study, the mathematical model in the rotating \(dq\)-reference frame is formulated as follows:
$$
\begin{aligned}
u_d &= R_s i_d + L_d \frac{di_d}{dt} – \omega_e L_s i_q \\
u_q &= R_s i_q + L_q \frac{di_q}{dt} + \omega_e (L_s i_d + \psi_f)
\end{aligned}
$$
where \(u_d\), \(u_q\) denote the \(d\)- and \(q\)-axis stator voltages, \(i_d\), \(i_q\) represent the corresponding currents, \(R_s\) is the stator resistance, \(L_d\), \(L_q\) are the inductances, \(\omega_e\) is the electrical angular velocity, and \(\psi_f\) is the permanent magnet flux linkage. For a surface-mounted PMSM where \(L_d = L_q\), the electromagnetic torque simplifies to:
$$
T_m = \frac{3}{2} P_n i_q \psi_f
$$
This linear relationship between torque and \(q\)-axis current enables effective torque control through current regulation. The vector control strategy with \(i_d = 0\) was implemented, coupled with space vector pulse width modulation to achieve precise torque tracking.
2.2 Powertrain Dynamics Model
The electric vehicle powertrain was modeled using a lumped-mass approach with seven degrees of freedom, incorporating the motor rotor, reduction gear pairs, drive shafts, wheels, and equivalent vehicle mass. The gear mesh dynamics were characterized by:
$$
\delta_y = R_1 \theta_1 – R_2 \theta_2
$$
$$
F_m = K_{12} \delta_y \cos\alpha_b + A_{12} \dot{\delta}_y \cos\alpha_b
$$
where \(R_1\), \(R_2\) are gear base radii, \(\alpha_b\) is the base helix angle, and \(K_{12}\), \(A_{12}\) denote mesh stiffness and damping coefficients. The complete torsional dynamic equations of the powertrain system can be expressed as:
$$
J_m \ddot{\theta}_m + k_{ms}(\theta_m – \theta_1) + c_{ms}(\dot{\theta}_m – \dot{\theta}_1) = T_m
$$
$$
J_1 \ddot{\theta}_1 + k_{ms}(\theta_1 – \theta_m) + c_{ms}(\dot{\theta}_1 – \dot{\theta}_m) + r_1 F_{y1} = 0
$$
$$
J_2 \ddot{\theta}_2 – r_2 F_{y1} + k_{gs}(\theta_2 – \theta_3) + c_{gs}(\dot{\theta}_2 – \dot{\theta}_3) = 0
$$
$$
J_v \ddot{\theta}_v – 2k_t(\theta_w – \theta_v) – 2c_t(\dot{\theta}_w – \dot{\theta}_v) + T_L = 0
$$
The driving resistance acting on the electric vehicle includes rolling resistance, aerodynamic drag, gradient resistance, and acceleration resistance, collectively expressed as the load torque:
$$
T_l = r \left( \delta m \frac{dv}{dt} + mg f \cos\alpha + mg \sin\alpha + \frac{1}{2} C_d A \rho v_r^2 \right)
$$
2.3 Simulation of Acceleration Dynamics
The combined electromechanical coupling simulation model was constructed in Matlab/Simulink by integrating the motor vector control model with the powertrain dynamics model. Simulation was conducted with a step torque command of 100 Nm and a torque rise time of 0.2 s over a duration of 3 seconds. The results reveal significant transient oscillations in both the motor shaft torque and half-shaft torque, which subsequently propagate to the vehicle body. Figure 2.13 in the original research demonstrates that the longitudinal acceleration exhibits pronounced oscillatory behavior during the torque transient phase, with the vehicle experiencing noticeable longitudinal jerking before gradually converging to steady-state values.
Parametric studies were performed to evaluate the influence of torque rise time and half-shaft stiffness on vehicle dynamic response. Three torque rise times were considered: 0.1 s, 0.14 s, and 0.18 s. The simulation results indicated that a shorter torque rise time produces a more rapid torque application, resulting in more severe longitudinal acceleration oscillations and higher jerk amplitudes. The peak acceleration values occurred at different times corresponding to each torque command profile. When half-shaft stiffness was varied within the range of 10,000 to 20,000 Nm/rad, the influence on dynamic response was comparatively minor relative to the torque rise time effect.
3. Experimental Study of Subjective and Objective Evaluation
3.1 Subjective Evaluation Methodology
The subjective evaluation framework was developed based on the widely adopted SAE J1441 ten-point rating scale, providing a standardized scoring language for trained evaluators to quantify their perceptual experiences during vehicle acceleration. The evaluation criteria specifically emphasized longitudinal dynamic comfort, with a focus on identifying abnormal shocks, longitudinal oscillations, and overall acceleration smoothness. The subjective scoring criteria are elaborated in the subsequent table.

